callsret.blogg.se - Can get my sentry safe open

#Can get my sentry safe open install#
#Can get my sentry safe open code#

The lock will fl ash once every fi ve (5) seconds during time delay and will fl ash once every second during the last ten (10) seconds of the time delay ending with a double signal. (During the time delay period the keypad will not respond to any entries)

Press * or # to initiate the Time Delay.

#Can get my sentry safe open code#

The lock will indicate a valid setting change with a single signal.Įxample: # – Master Code – # – 05 – # – 05 – #, this will set a fi ve (5) minute time delay.

This function will delay both the opening and programming of the lock.

Time delay modeĪlways perform this operation with the door open. The lock will indicate a valid setting change with a single signal.Enter: # – Master Code – # – 0 – # – 0 – #.Turn the handle clockwise before the green light disappears Returning to single user mode (Single code to unlock).The lock will indicate a valid code entry with a single signal and the open light will stay green for fi ve (5) seconds.Enter: # – Master Code – # – 2 – # – 2 – #.Master or Manager Code + User Code to unlock Enter: # – Master Code – # – 1 – # – 1 – #.Always perform this operation with the door open. One person enters their code and within sixty (60) seconds, the second code is entered. When you want two people to open the safe set your safe to dual user mode. Enter: User ID Number (3-7) – * – # – # Dual user mode.Deleting user codesĪlways perform this operation with the door open. The Master and Manager can also change the user codes by following the “Activate userĬodes” section steps 1 thru 3. The lock will indicate an invalid code change with a double signal and the old code is still valid.Test the new code several times before closing the door: Enter: * – Code – # If a mistake is made during the change, wait thirty (30) seconds and repeat steps 1 thru 3. Enter: New User Code – # – New User Code – #, before the orange light disappears.Changing the user codeĪlways perform this operation with the door open The lock will indicate an invalid code entry with a double signal and the old code is still valid.Įxample: # – Master Code or Manger Code – # – 5 – * – New User Code – # – New User Code – #.

The lock will indicate a valid code entry with a single signal.

If a mistake is made during the activation, wait thirty (30) seconds and repeat steps 1 thru 3.

Enter: User ID Number (3-7) – * – New User Code – # – New User Code – #, before the orange light disappears.

Enter: 2 – * – New Manger Code – # – New Manager Code – #, before the orange light disappears.

The set light will stay orange for ten (10) seconds.

Enter: # – Master Code or Manager Code – #.

(Code length: 1 to 10 digit code) Always perform this operation with the door open.

The lock will indicate a valid code change with a single signal.

Keep notes on which code belongs to which user (Master (User 1), Manager (User 2), User 3, User 4, User 5, User 6 and User 7).Ī single signal (LED fl ashes and beeps once) response from the lock indicates valid entry. You should set the lock to your own unique master & manager code immediately. The SentrySafe electronic lock is shipped from the factory with a factory set master code

Turn the handle clockwise before the green light disappears.

Enter: * – Master or Manager Code (from front of booklet) – # The lock will indicate a valid code entry with a single signal and the open light will stay green for five (5) seconds.

Pinched cables result in a short circuit. Ensure that there are no wires or cables trapped between the keypad and the mounting plate.

Carefully position the keypad into the inserts on the mounting plate and turn clockwise.

Caution: Hold onto the keypad housing to avoid pulling wires.

#Can get my sentry safe open install#

Install four new AAA Alkaline batteries (not included).

Turn the keypad housing counter clockwise and carefully pull away from the mounting plate to expose battery compartment.

Installation of the batteries (keep door open during setup):